all settings were reset to default values что делать msi
«All settings were reset to default values.» Message
legaianlight
New member
Hello again! I was unsure where to put this, so i settled on the MOBO Forum.
Today, when I went to boot up my computer, I got, roughly, the following message:
«All settings were reset to default values. The previous overclock settings have failed, system has been restored to its default settings.»
Then it gives some options as to what to do. I tried all the options, finally getting my computer to get past the above message by telling it to «Press F2 to load default values and continue.»
After doing that, I tried re-overclocking the computer just to see if it was some sort of glitch, and whenever I do so (I used the following link as my guide: https://www.msi.com/blog/intel-9th-cpu-overclocking-5ghz-with-z390-motherboards ), I get the same «All settings were reset» message and have to press F2 to get things working again.
Additionally, and perhaps related, now my computer takes much longer to start up. It almost seems as if it is waiting for my keyboard to connect, which seems weird as it is a wired keyboard and I’ve never had it take so long for the keyboard to light up and become functional before.
I did try flashing the bios once i got things working, but still, the problem persists.
rb_leroy
Active member
Chike
Active member
Even when overclocking fails you should be able to get back into bios.
Clear cmos and see that pc boots normally.
What are you trying to achive?
Make changes one at a time, save known good settings to oc profile, you can easily restored.
Make our lives easier and put your system specs in your forum signature >>Posting Guide
legaianlight
New member
Chike
Active member
So even just enabling xmp cause this error?
Which model is the ram F4-3200C16D-32GVK or F4-3200C16D-32GVKA?
On the qvl there is F4-3200C16D-32GVR, so I assume at leat the F4-3200C16D-32GVK should be compatible.
Please post a screen capture of HWiNFO, with the default settings, if possible under some load (like prime95, no avx, large fft).
In particular I am looking for the motherboard and cpu voltages.
legaianlight
New member
Just double checked, as the first time I enabled XMP, I may have unintentionally changed some of the other settings. the problem does indeed occur after just enabling XMP.
I have the F4-3200C16D-32GVK.
Attached you will find the HWINFO picture. Please let me know if I didn’t capture the correct information or if you need it under even more of a load.
Edit: Also, since I didnt mention it before, I’ve had this setup since early August with no major problems, other than some lighting issues initially. The overclocking seemed to work fine until I turned it on today.
Attachments
Chike
Active member
The sensors window, sorry i was not clear.
You can expand the window by clicking the out arrow on the bottom left if you cannot fit all the cpu and motherboard voltages in one screen.
like so, differet names of course:
legaianlight
New member
Ah, sorry about that. Thanks for your help, by the way.
I found the sensors window, but when I tried to put multiple sensors on one page with the button you mentioned, sometimes the data would go off screen, making it difficult to capture everything you wanted in one go. As such, I took 6 different pictures to hopefully get you the information you were asking for.
Attachments
Chike
Active member
Lets try xmp with a few modification.
Go to oc section and change to expert mode.
Select xmp profile, and manually select 3000mhz for memory frequency.
Change vccio and vccsa from auto to their default values shown on the left.
Save and reboot. If no failed overclock message, change memory frequency to auto and try again.
If any of the above fail, press F1 and increase vccio and vvcsa a notch, 0.005v to 0.01v at a time. For now don’t go over 1.1v for either of them though I saw cases people use over 1.2v.
I think that with F1 bios changes should remain intact even it booted with default values, not sure,
legaianlight
New member
Just to verify, I:
1) Enabled Extreme Memory Profile.
2) Changed DRAM Frequency to DDR4-3000 (30×100.00×1.00)
3) Changed CPU SA Voltage to 1.050 (tried to do 1.058, which is the voltage listed to the left, but it auto-converted to 1.050)
4) Changed CPU IO Voltage to 0.950 (Tried to do 0.958, which is the voltage listed to the left, but it auto-converted to 0.950)
Perhaps i was changing incorrect values?
Chike
Active member
legaianlight
New member
As such, I just got around to trying the individual memory modules in the dimma2 and dimmb2. I tried both modules individually in both slots, and when I try to use XMP, I get the same message as I wrote in about. I also tried both at the same time in the dimma1/dimmb1 slots, but I got a message that those slots were not optimized.
Just to share my thoughts, when I was trying to re-overclock after I started getting this error, I don’t *believe* I was messing with the memory overclocking. Now as I mentioned before, I’m a bit of a scrub when it comes to this stuff, so I may have been messing with the memory without realizing it, but I just wanted to make y’all aware of this.
Also, as I think i mentioned earlier, my computer boots up much slower now, much slower than one would expect just from losing the ability to overclock. It’s almost as if it’s waiting for my keyboard to become recognized, but I’m not 100% sure what the deal is.
Thanks for all your help so far, especially you, Chike.
Chike
Active member
So enabling xmp give the failed overclock message in any slot with either of the modules?
Can you check CPU-Z spd tab, to see who is the dram manufacturer?
Now it is booting slow even with default settings?
legaianlight
New member
So enabling xmp give the failed overclock message in any slot with either of the modules?
Can you check CPU-Z spd tab, to see who is the dram manufacturer?
Now it is booting slow even with default settings?
More or less. I tried the individual modules ind a2 and b2 by themselves, but since it told me the slots werent optimized, I only tried both modules once in A1 B1 together once, and then I did not try overclocking since I got the «unoptimized» message.
Checking in CPU-Z, I show that G.skill was the module manu, and that SK Hynix was the dram manu.
And yes, ever since I started getting this message (The «all settings were reset» one), It takes about 30 seconds to reach the screen where you can opt to enter the bios, and it takes about 30 more seconds to get to the screen where you get to select which disc you want to boot from, whereas it used to take about 20 seconds from the time I pressed the power button til I could enter my password and login. After that, it’s pretty fast. But like I said, it’s almost as if the keyboard is taking a long time to be recognized, and therefore the computer is waiting for it to be recognized so that I can use it to, for example, press DEL to enter the bios.
Chike
Active member
It was the sk hynix i was after, that mean it’s the same module in the qvl F4-3200C16D-32GVR.
Can you still return the board for a replacement, that what I would do next.
legaianlight
New member
Chike
Active member
melvin.p
New member
I have been using this gear for a bit more than 1 year now (almost every day, for working/developing/intensive gaming as well).
The bios had been updated to 7B10v14 at the time and XMP was activated since then : and then I never really came back to the bios settings, except a few months later to play w/ the UEFI settings and the boot priorities to allow a dual boot through grub (to switch between Win10/Linux).
On top of the issue mentioned above, my boot became much slower to reach the splash screen, just like described by the OP here.
I then :
— deactivated / reactivated the fastboot option (not the MSI one, but the default one) : nothing changed (still same error message saying : «all settings were reset to default. etc.»).
— flashed the BIOS to the latest current version (7B10v14) : nothing changed.
— deactivated the default XMP choices (3200Mhz, 16-18-18-38, 1.35V) to select a lower profile @3000Mhz : nothing changed
— same but with a profile @2600Mhz : nothing changed.
— played with the voltage to increase it a bit : nothing changed.
— Went back to my initial profile, but I simply deactivated the XMP : it worked.
So here we go, I reseated my 4 memory sticks (they already seemed very well tightly seated in their slots, you can feel that this godlike board wont let them escape easily. ), changing them from slot (didnt pay too much attention here, I think I only changed 2 of them), and. voil. the pc booted very quickly. it seemed like a good sign, so I directly entered the bios settings to activate the default XMP settings (3200Mhz, 1.35V) and well. it worked!
Press f1 to run setup press f2 to load default values and continue что это, как исправить?
Приветствую. BIOS — настройки ПК, которые влияют на работу железа, не имеют отношения к Windows, влияют только на аппаратную работу компьютера. Изменять опции в BIOS без необходимости/должного опыта не стоит. Однако иногда и здесь могут быть неполадки.
Разберем название
Также в названии может быть указана фраза Please enter setup to recover bios setting, которая означает: пожалуйста зайдите в биос чтобы восстановить настройки.
Причины
Причиной может быть севшая батарейка CMOS на материнской платы. В таком случае еще может указываться надпись CMOS CheckSumBad. Данная батарейка необходима чтобы настройки в биосе сохранялись даже после выключения ПК. Решение — просто заменить батарейку, купить можно в любом компьютерном магазине. Чтобы заменить: нужно разобрать ПК, осторожно извлечь старую и установить новую. Примерный вид батарейки:
В названии могут встречаться дополнительные слова, подсказывающие характер ошибки, например:
Заключение
При наличии ошибки Press f1 to run setup press f2 to load default values and continue, попробуйте:
Комментарий с форума, возможно будет полезным:
all settings were reset to default values
RPI.su — самая большая русскоязычная база вопросов и ответов. Наш проект был реализован как продолжение популярного сервиса otvety.google.ru, который был закрыт и удален 30 апреля 2015 года. Мы решили воскресить полезный сервис Ответы Гугл, чтобы любой человек смог публично узнать ответ на свой вопрос у интернет сообщества.
Все вопросы, добавленные на сайт ответов Google, мы скопировали и сохранили здесь. Имена старых пользователей также отображены в том виде, в котором они существовали ранее. Только нужно заново пройти регистрацию, чтобы иметь возможность задавать вопросы, или отвечать другим.
При загрузке компьютера выводится текст и сообщение:
«cmos settings wrong
cmos date/time not set
press f2 to run setup
press f1 to load default values and continue»
CMOS настройки неправильно
Дата CMOS / время не установлены
Нажмите F2, чтобы запустить программу установки
Нажмите F1, чтобы загрузить значения по умолчанию и продолжить.
Если нажимаю F1, то дата и время устанавливаются не правильно — 2008 г, приходится постоянно через F2 загружать. Что за проблема?
Возможно стоит заменить баиарейку на материнской плате на новую.
В биосе возможно есть опция Hold on Alerts которую надо отключить чтоб зарузка шля дальше сама,
какая у вас версия биос? ее можно глянуть в биосе на самом верху, либо при старте ПК на первом экране.
но причина где-то в другом. КМОС слетает вероятно изза батарейки.
Эта проблема — одна из самых примитивных, справиться с которой вполне способен и первоклассник (если он знает, что внутрь компьютера нельзя лезть, не отключив его от сети).
Покупается батарейка CR2032 и заменяется (на материнской плате установлена, необходимо соблюдать полярность — той же стороной ставить, как старая стояла!). Вынимать без помощи металлических предметов! Чем-нибудь пластиковым или деревянной зубочисткой.
Потом время установите правильное и года три не будет беспокоить.
Цена вопроса — 25-30 рублей, если не покупать какую-нибудь очень именитую батарейку (разницы — никакой, кроме цены).
Is there any way to «reset» all setup settings in Inno Setup into their default values?
I hope you understand what I want to accomplish. If the application is already installed, then set all options to the last-installation values, if the app is not installed, then set them to default values.
I know the setup does all of this at it’s startup, but I want to add a button, which would revert all the changes user made (eg. in wpSelectComponents ) to their setup-startup defaults. How can I do that?
All settings were reset to default values что делать msi
в самом низу что написано
что написано конкретно?
Please enter Setup to recover BIOS setting
Press F1 to Run Setup
Press F2 to load default values and continue
что если с компом что то случилось, сразу валят на детей.
У нас так, к сожалению. Кто смотрит тот и отвечает(
Проходит POST, самопроверку то бишь.
И не находит винду по тем или иным причинам.
Фото экрана приложите.
через модем сидите?
Телефон могу чз ватсап отправить 89141051481
Комп просит восстановить настройки Bios
Please enter Setup tu recover Bios setting
F1 to Run SETUP
F2 to load default values and continue
F2 нажимать не пробовали?
а вдруг просто батарейка кончилась у биоса?
точно батарея села, при каждом запуске дата будет старая
Во сколько обойдется замена батареи и меняют ли вообще(
F2 пробовала бесполезно((
Дети зло не заводите их. Все ломают портят и никакой личной жизни!
купите в магазине компьютерном
батарейки от 15 до 65 руб.
да, и дети тут совсем ни при чем:)
если F2 не помогает, то возможно проблема не только в батарейке
по идее без батарейки система должна запуститься с настройками биос по умолчанию и с неправильной датой
хард по умолчанию другой стоит
наверное а винда на другом. Настройке биосе посмотрите
вот скрин который скинул автор
На F2 не реагирует не перезагружается. Выключаю из розетки.
Будешь натерать веревку мылом бери Dave
Ведь он на четверть состоит из увлажняющего крема и не сушит кожу.
с дисковода CD вытащите и перезагрузите комп
Флешку, планшет или телефон из USB-порта вытащите.
сдохла клава и батарея биос
лучше позовите знающего человека
и лучше, чтоб этот человек был хорошо вам знаком, а то наши «спецы» с объявлений могут всякую хрень придумать, типа материнку надо сменить и т.п.
Комп походу вообще древний с ddr2 погляжу
смысла убивать вообще не вижу, выкинуть бы по хорошему не мешало 🙂
Поди монитор ЭЛТ?
может батарейка села, все таки старая вещь у вас. попробуйте поменять таблетку
Нет) Я все еще жива)))
Проблема. Как это лечится?
Сигнатура проблемы:
Имя события системы: BlueScreen
Версия ОС: 6.1.7601.2.1.0.256.1
Код языка: 1049
Дополнительные сведения об этой проблеме:
BCCode: 19
BCP1: 0000000000000020
BCP2: FFFFFA80097FA0A0
BCP3: FFFFFA80097FA0C0
BCP4: 000000000402000A
OS Version: 6_1_7601
Service Pack: 1_0
Product: 256_1
Файлы содержащие сведения об этой проблеме:
C:\Windows\Minidump\121415-5538-01.dmp
C:\Windows\Users\Олег\AppData\Local\Temp\WER-12386-0.sysdata.xml
Проблема не лечится переустановкой Windows. Подозреваю что проблема в железе.
Олег задал(а) этот вопрос 14 декабря 2015
Ответы:
Также удалите из системы Windows все программы и драйвера, которые появились незадолго до проблемы. Лучше откатить систему назад. Может проблема в софте? Даже в первую очередь начните с этого.
Ну как-то так. процесс довольно муторный, и найти причину не просто и не быстро.
Олег | 15 декабря 2015, 19:42
Система вылетала три раза, на четвертый Windows перестала запускаться, надпись на черном экране: All settings were reset to default values. The previous overclock setting have failed, system has been restored to its default settings. После переустановки полностью все обновил, операционку, все драйвера системной платы и видеокарты с сайта разработчика. Приблизительно неделю работал комп нормально, потом при просмотре видео онлайн через браузер произошел сбой, без синего экрана, просто все потухло и комп начал перезагружаться, правда уже с другого жесткого диска, но поскольку там нет операционной системы, то выдало ошибку: NTLDR is missing. Настройки биоса оказались сброшенными. Выставил все как было, система запустилась и три дня работала нормально. Вчера вечером опять синий экран.
Alek55sandr5 | 15 декабря 2015, 11:47
Начнем с того что у вас Windows 7. И первое что нужно сделать это обновить (если не обновлена) систему до Service Pack 1. Если это не помогло, то далее вам нужно обновить драйвера установленных устройств. В первую очередь нужно обновить драйвер видеокарты. Также проблема может быть в какой-то конкретной программе. Подумайте, после установки какой программы начал появляться синий экран и удалите эту программу. Удаление программы лучше осуществить при помощи Revo Uninstaller.